Zahranvane.com Вход в профила

Количка

Количката Ви е празна.
 

Акселерометър и жироскоп с MPU-6050

Продуктов код:  •  131-06  •  
Производител:
Наличност:
2
Цена:         без ДДС / с ДДС:
1 бр. : 9.60 лв. / 11.52 лв.
≥ 2 бр. : 9.10 лв. / 10.92 лв.
Документация
  MPU-6000-Datasheet1.pdf
 

Модул акселерометър и жироскоп с MPU-6050

MPU-6050 е миниатюрен, тънък и с ниска консумация цифров акселерометър за 3 оси и жироскоп за 3 оси с голяма прецизност като изходните данни са достъпни по 16-битови SPI или I2C интерфейси.

Предимства

          Gyroscope Features

  • The triple-axis MEMS gyroscope in the MPU-60X0 includes a wide range of features:
  • Digital-output X-, Y-, and Z-Axis angular rate sensors (gyroscopes) with a user-programmable full-scale range of ±250, ±500, ±1000, and ±2000°/sec
  • External sync signal connected to the FSYNC pin supports image, video and GPS synchronization
  • Integrated 16-bit ADCs enable simultaneous sampling of gyros
  • Enhanced bias and sensitivity temperature stability reduces the need for user calibration
  • Improved low-frequency noise performance
  • Digitally-programmable low-pass filter
  • Gyroscope operating current: 3.6mA
  • Standby current: 5μA
  • Factory calibrated sensitivity scale factor
  • User self-test

    Accelerometer Features
  • The triple-axis MEMS accelerometer in MPU-60X0 includes a wide range of features:
  • Digital-output triple-axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g
  • Integrated 16-bit ADCs enable simultaneous sampling of accelerometers while requiring no external multiplexer
  • Accelerometer normal operating current: 500μA
  • Low power accelerometer mode current: 10μA at 1.25Hz, 20μA at 5Hz, 60μA at 20Hz, 110μA at 40Hz
  • Orientation detection and signaling
  • Tap detection
  • User-programmable interrupts
  • High-G interrupt
  • User self-test

    Additional Features
  • The MPU-60X0 includes the following additional features:
  • 9-Axis MotionFusion by the on-chip Digital Motion Processor (DMP)
  • Auxiliary master I2C bus for reading data from external sensors (e.g., magnetometer)
  • 3.9mA operating current when all 6 motion sensing axes and the DMP are enabled
  • VDD supply voltage range of 2.375V-3.46V
  • Flexible VLOGIC reference voltage supports multiple I2C interface voltages (MPU-6050 only)
  • Smallest and thinnest QFN package for portable devices: 4x4x0.9mm
  • Minimal cross-axis sensitivity between the accelerometer and gyroscope axes
  • 1024 byte FIFO buffer reduces power consumption by allowing host processor to read the data in bursts and then go into a low-power mode as the MPU collects more data
  • Digital-output temperature sensor
  • User-programmable digital filters for gyroscope, accelerometer, and temp sensor
  • 10,000 g shock tolerant
  • 400kHz Fast Mode I2C for communicating with all registers
  • 1MHz SPI serial interface for communicating with all registers (MPU-6000 only)
  • 20MHz SPI serial interface for reading sensor and interrupt registers (MPU-6000 only)
  • MEMS structure hermetically sealed and bonded at wafer level
  • RoHS and Green compliant

Продуктът се намира в категории:
 
Свързани продукти